Other

Travel reduction clips for Cane Creek suspension forks. - Cane Creek Helm Air Travel Reduction Clips, Set of Two 10mm Clips

40-Series Bearing - Compatible with 110-, 40-, and 10-Series headsets

Crown races for Cane Creek headsets fit a variety of lowers and crown race seat diameters. - Compatible with 10-, 40- and 110-Series headsets and backwards compatible with S and XX Series - Integral mold seals keep out the elements - Compatible with 52mm lower headset bearings - Compatible with 40mm (1-1/2") tapered steerer tubes - Lightweight aluminum construction

Cane Creek crown races are interchangeable between headset series.

Bearings for Cane Creek AER headsets. - Aluminum Bearing

40-Series Bearing - Compatible with 110-, 40-, and 10-Series headsets

A higher quality spring greatly improves the performance of your coil shock. VALT springs from Cane Creek are much lighter than traditional steel springs while pushing the boundaries of performance and durability. - Inner diameter of 36.5mm is compatible with all Cane Creek coil shocks - Also compatible with Manitou, Marzocchi, XFusion, ELKA/MRP, BOS and DSP - Compatible with Fox coil shocks with required spring clip adaptor

Cane Creek Progressive Rate VALT coil springs are designed to provide riders with a true rise-in-rate spring curve. - Springs feature the progressiveness and ramp-up that hard-charging riders demand - Designed for use with Cane Creek Coil shocks - Progression begins at 50% into the stroke of the spring - Crafted from high-performance spring steel - Inner diameter of 36.5mm is compatible with all Cane Creek coil shocks

These baseplates are the foundation that keeps Chris King headsets turning with legendary smoothness. Manufactured from high-quality stainless steel or titanium, Chris King makes replacement baseplates for all standard sizes and a number of ingenious solutions for those that need something a little special to make their headset work. - Engineered and manufactured in Portland, Oregon USA - High-quality stainless steel and titanium baseplates available for all standard Chris King headset sizes - Titanium baseplates are available in 1-inch and 1 1/8-inch sizes only - Devolution baseplates are a stainless steel solution that allow King headsets to adapt to a wide variety of steerer tube sizes - King Stainless Steel baseplates are available in undersized and oversized versions for irregular steerer tube sizes - 30.0mm ID/40.5mm OD for post-April 1995 1-1/8" Headsets - 30.0mm ID/44.0mm OD for pre- April 1995 1-1/8" Headsets

Dropper remote optimized for drop bar gravel bikes. - Single mounting bolt for left-hand actuation - Two-way drop actuation for use in multiple hand positions - Compatible with Highline and other cable-actuated dropper seatposts - check with your seatpost manufacturer.

- Aluminum straddle cable carrier for cantilever brake

Dimension Seatpost Clamps - Diameters: 28.6mm, 30.0mm, 31.8mm, 35.0mm - Weight: 34g

Dimension Stem Column Adaptors - Total quill length 180mm - Measurement from minimum insertion to top of steerer adaptor is 118mm - Alloy - Quill insertion diameter: 1-inch

ABI Headset Bearing for new builds or replacements.

FSA bearings that set directly into the frame without the use of pressed in cups. - 36/45 degrees is Cane Creek-compatible - 45/45 degrees is Campagnolo-compatible

- Allows use of a 1-1/8" threadless stem in combination with a threaded 1" headset/steerer - 22.2 quill diameter - 50mm stem clamp area

-Seatpost clamp spacer kit for Advanced ISP models (2012-2014)

-1-1/4" headset spacer kit with following sizes: 2.5mm(x1) .5mm(x2) 10mm(x2)

- Disc rotor lockrings to securely mount Center Lock rotors - Available for standard or oversize QR or thru-axle hubs

- Half-link connector allows you to add or subtract half of one link (1/2 inch) from the chain in order to optimize chain tension - Uses standard chain pin connector and tool

- Allows quick chain removal without tools - MissingLink 410HD|~|1sp|~|BMX Heavy Duty chain|~|9.4mm|~|each|~| - MissingLink 410|~|1sp|~|BMX|~|8.6mm|~|each|~| - MissingLink II|~|8sp|~|all|~|7.1mm|~|6/card|~| - MissingLink-9|~|9sp|~|all|~|6.6mm|~|6/card|~| - MissingLink-10R|~|10sp|~|KMC, Shimano, SRAM|~|5.9mm|~|6/card|~| - MissingLink-10CR|~|10sp|~|Campagnolo only|~|5.9mm|~|6/card|~| - MissingLink-11|~|11sp|~|Campy, KMC, Shimano|~|5.5mm|~|6/card|~|

- Compatible with Shimano HG40/50/70/90 chains - KMC Z50, Z7, Z8, X8.93, X8.99 chains - Reusable - No Tool Required - Pin Length: 7.3 mm

Use to create your desired chain length in single-speed applications. Only one half link is needed. - Non-reusable - Width: 9.4 mm - Drivetrain Speeds: 1 - Color: Black - Chain Compatibility: Shimano , SRAM , Campagnolo , Connex , KMC

- Missing links to make chain installation, maintenance and reparation easier - Card of 2

KMC Missing Link connectors are for use on new chains or to keep in your seat bag for an emergency repairs. - Compatible with KMC and Shimano 10-speed chains - Includes 2 pairs

- Missing links to make chain installation, maintenance and reparation easier - Card of 2

Parts for the service of the seal and restore the smooth cycling of KS dropper posts.

- 2Mm powertex neoprene that prevents nicks and scratches while reducing the noise of chain slap - Tightly stitched with heavy-Duty thread to add extra strength and durability - Jumbo: Taper (95Mm to 85mm and is 254mm in length) - Standard: Taper (85Mm to 75mm and is 254mm in length) - Super jumbo: Taper (117Mm to 107mm and is 254mm in length) - Jumbo 29er: Taper (95 Mm to 85 mm and is 295 mm in length) - Swingarm: Taper (183Mm to 175mm and is 227mm in length)

Disc brake adaptors designed to mate Magura disc brakes with a variety of frame mounts and rotor sizes. - Includes hardware to mount adaptor to frame

Disc brake adaptors designed to mate Magura disc brakes with a variety of frame mounts and rotor sizes. - Includes hardware to mount adaptor to frame